Need help for Ethernet communication to PM554

I have PM554 ETH CPU. Now I want to connect my CPU to Automation Builder using Ethernet IP. I am trying to Scan the IP throuch Automation Builder but it is unable to scan any CPU.

I also want to Factory RESET the PM554 CPU. The procedure I followed to reset is

1. Power off cpu.

2. Keep DIP switch on STOP mode.

3. Power on CPU again.

4. Wait until Run LED stops blinking.

I have tried this. But after Power on RUN LED keeps on blinking. And I am unable to RESET the cpu.

So provide the RESET procedure.

Thank you.


Associated Apps

AC800M as Modbus Slave (1.0)  Download

Hands on Manual for Profinet Communication with AC800M (1.0)  Download

Automation Builder version 1.1/1.2 Installation & Activation Guide (1.0)  Download


Add New Comment


jjshah1   

asked 4 months ago
Closed



Answers

1

Hi

have you tested with IP scan utility?

The cpu is used or new?

Have you only Eth cable or can you test access the cpu with COM port - TK503 cable?

If you give us more information, we can help you better

Flavio Mussolin   

answered 4 months ago


 


By jjshah1 on 6/15/2017 | Like (0) | Report

Yes I have tested with IP scan utility. But it is unable to scan CPU. I also have tried to Force IP. But that is alo not working.

I do not have TK503 cable.

The problem is I am unable to reset the CPU. So please give me procedure to reset the CPU PM554


By Flavio Mussolin on 6/15/2017 | Like (0) | Report

If you can not read the IP address of the CPU from Automation Builder with IP SCAN you must first, make sure the PC has enabled the port and it works properly.
Then, you can consider that the eth port of CPU is damaged and anyway the cpu reset does not affect the read / access the cpu via eth


Add New Comment



Get weekly AKS updates


Partner Exclusive Webinars

 

> – Login to the partner portal to register



Points Redemption Program - Redeem your points for ABB training, Bluetooth speakers and mugs. Terms and conditions >


Earn points when you refer a friend
AKS Referral Program is "Live" - Learn more



AKS Experts


avatar
Ask Harsha.D   

Rank: 6

Tech.Support,software and commisioning engineer with Proficient knowledge in 800xA and its products, RNRP,Networking in general.


avatar
Ask Flavio Mussolin   

Rank: 4

ABB AVP, Senior Electronic and Automation Engineer with over 30 years of experience in the field of process automation automotive, pharmaceutical, hollow glass, steel and rolling.


avatar
Ask kstoilov   

Rank: 16

Control System Engineer: 800xA, Compact 800, AC500, AC31-50, Advant Master, Simatic, AC&DC Drives 11 years worked for ABB - Control Systems


avatar
Ask nikismith   

Rank: 261

I have been a part of the Recording & Control Factory team for 17 years in total, having spent a number of years as a repairs technician withi the manufacturing department, but being in my current role for 9 years now.


avatar
Ask Rob Lyon   

Rank: 3

info@lymac.co.nz I'm an independent DCS software and commissioning engineer with extensive experience in 800xA and other ABB products. I've worked in almost every corner of the world and still haven't seen it all.


avatar
Ask MMM   

Rank: 5

ABB PA CT Technical Support


avatar
Ask Govindaraj   

Rank: 10

Working in ABB India Operation Center. Have Project engineering and commissioning experience in ABB 800xA, Freelance, AC500.


avatar
Ask Dieter Henkel   

Rank: 23


avatar
Ask Stefan Stromqvist   

Rank: 1

I joined ABB in the year of 1994 and has since 1999 been working as a Service & Support Engineer at BU Control Technologies in Västerås, Sweden. My areas of expertise are: 800xA Base, 800xA for Advant Master, Information Management, operating systems, RNRP and Ethernet comms/networking in general.


avatar
Ask Sumit Gargav   

Rank: 2

I have worked with Freelance in majority, with 800xA FD and Melody system partly. Also had opportunity to work with Protocols - HART,Profibus,FF & Modbus.